Steel sprocket. Replaces JT Sprockets JTR215-49.
Steel sprocket. Replaces JT Sprockets JTR215-55.
Equivalent to Twin Air 150004. This will suit the following models as well as those listed in fitments: Honda CR80 R2-T,V,W,X,Y,1,2 Expert 1...
Steel sprocket. Replaces JT Sprockets JTF1256-14.
Steel sprocket. Replaces JT Sprockets JTF1256-15.
This will suit the following models as well as those listed in fitments: Honda CR80 R2-T,V,W,X,Y,1,2 Expert 1996-02. Honda CRE80 All Years. ...
Thread 14mm x hex 3/4" (19mm) x pitch 1.25mm. Ceramic resistor. Heat range 10. 19mm (3/4") reach. 0.6mm fine wire iridium centre e...
Performance Upgrade: Replaces worn, damaged parts with, in many cases, upgraded materials like high-performance interface gasket material fo...
Thread 14mm x hex 3/4" (19mm) x pitch 1.25mm. Ceramic resistor. Heat range 10. 19mm (3/4") reach. Fine wire nickel alloy centre el...
Brand: JT Sprockets. Position: Rear. Tooth Count: 56. JT Part Number: JTR215.56. Type: Standard. Material: Steel. Fitment: Direct replacemen...
Brand: JT Sprockets. Position: Rear. Tooth Count: 49. JT Part Number: JTR215.49. Type: Standard. Material: Steel. Fitment: Direct replacemen...
Brand: JT Sprockets. Position: Rear. Tooth Count: 55. JT Part Number: JTR215.55. Type: Standard. Material: Steel. Fitment: Direct replacemen...
This engine gasket set contains most of the gaskets required for an engine rebuild. This gasket set does not include any oil seals other tha...
Outer diameter 12.7mm. Length 37mm. Spring length 40mm. Made in Japan. Replacement aftermarket part for for the following OEM numbers: Honda...
Flat head countersunk bolts. Thread 8mm. Length 28mm. Pitch 1.25mm.
Type: K1. 4.40mm x 13.60mm. Can use with or without clip. Made in Japan. Replacement aftermarket part for the following OEM numbers: (Note: ...
Thread 8mm. Spanner size 12mm.
Outer diameter 12.7mm. Length 37mm. Spring length 40mm. Replacement aftermarket part for for the following OEM numbers: Honda 43520-MJ6-315,...
Koyo 6201DDU. Double sided rubber sealed. Outer diameter 32mm. Inner diameter 12mm. Width 10mm. Made in Japan. Replacement aftermarket part ...
Includes all the parts you need for one caliper. OEM replacement, meets or exceeds OEM specs.
Outer diameter 18.20mm. Length 37.00mm. Thickness 2.80mm. Heavy duty clutch springs.
Piston outer diameter 27mm. This kit contains an inner oil seal and an outer dust seal. Fit Japanese bikes only unless stated otherwise. Rep...
This kit includes the following bearings: Bearing 1: ID 26mm x OD 47mm x Thickness 15mm. Bearing 2: ID 26mm x OD 47mm x Thickness 15mm.
Piston outer diameter 27mm. Each kit contains an inner oil seal and an outer dust seal. Enough seals for 5 pistons. Made in Japan. Fit Japan...
Piston outer diameter 30mm. Oil seal: 3.00mm wide x 3.20mm thick. Dust seal: 2.15mm wide x 2.15mm thick. This kit contains an inner oil seal...
Kit contains a pair of fork oil seals and a pair of fork dust seals. Dyno tested to last 3 to 4 times longer than OEM seals. Directional rib...
Includes all the parts you need. 52100 bearing steel, hardened and precision ground. OEM style clip seals. Full compliment needle or spheric...
Piston outer diameter 30mm. Each kit contains an inner oil seal and an outer dust seal. Enough seals for 5 pistons. Fit Japanese bikes only ...
Upper or Lower depending on whether standard or USD forks. Outer diameter 41mm. Inner diameter 37.1mm. Width 12mm. Thickness 1.95mm.
