39mm is the outside diameter of your carburettor intake. Overall length including rubber 50mm.
Brake caliper shaft boots are the rubber sleeves that protect the slide bolts. Replacement aftermarket part for the following OEM numbers: S...
Outer diameter 14.5mm. Inner diameter 12mm. Stem 7mm.
Please note: for models that have 14mm pins you will need to add 14mm bushes to your cart SKU: 019917. Suitable for early Japanese motorcycl...
39mm is the outside diameter of your carburettor intake. Total length 70mm.
Suitable for Sport, Touring and Off-Road Use. RX-Ring Chain. Standard Sealed Chain. Made in Japan. Specifications Plate thickness (inner): 2...
Comes with rivet link, no split link but these can be found under split links via search. The D.I.D ZVM-X Series utilizes our patented X-Rin...
Piston outer diameter 38mm. This kit contains an inner oil seal and an outer dust seal. Fit Japanese bikes only unless stated otherwise. Rep...
Piston outer diameter 38mm. Each kit contains an inner oil seal and an outer dust seal. Enough seals for 5 pistons. Fit Japanese bikes only ...
39mm is the outside diameter of your carburettor intake. Overall length including rubber 44mm.
Non-Sealed economical chain for heavy duty usage. Made in Japan. Specifications Plate thickness (inner): 2.30. Plate thickness (outer): 2.30...
Upper bearing: 25mm x 47mm x 15mm. Lower bearing: 30mm x 55mm x 17mm . Includes all bearings and seals. Heavy duty tapered roller bearings. ...
Comes with rivet link, no split link but these can be found under split links via search. This final drive chain is the correct length and p...
Please note: with the GL1100 the push rod that attaches to the brake pedal is not long enough so you will need to use your old one. With som...
Kit contains a pair of fork oil seals and a pair of fork dust seals. Dyno tested to last 3 to 4 times longer than OEM seals. Directional rib...
Note: The original relay for many of the Suzuki models (OEM #38610-45031) have the terminals pointing down but this one has the terminals or...
Outer diameter 36mm. Inner diameter 27mm. Depth 4mm. Flat Copper Exhaust Header Gaskets fit with flat side of the gasket against the cylinde...
Piston outer diameter 38mm. Each kit contains an inner oil seal and an outer dust seal. Enough seals for 5 pistons. Made in Japan. Fit Japan...
Made in Japan.
For use on 12v bulbs upto 23w.
Please Note: This switch may need modification to the single wire block by removing block and adding a male bullet connector and it only fit...
Height 65mm. Width 72mm. Replacement for Hiflofiltro HF133 & Champion X307. This filter does not come with an O-ring. Replacement afterm...
Steel sprocket. ID: 76mm. PCD (Pitch Circle Diameter): 100mm. Width: 9mm. Bolt hole ID: 10.3mm. Number of bolt holes: 6. Pitch: 530. Replace...
Replacement for FEW K83L; DK39L, DK27L, DT28L; Honda OE 30202-399-000; Kawasaki OE 21008-022; Suzuki OE 33160-45020.
Replacement for FEW K83R; DK39R, DK27R, DT28R; Honda OE 30203-399-000; Kawasaki OE 21008-021; Suzuki OE 33140-45020.
Brand: JT Sprockets. Position: Front. Tooth Count: 14. JT Part Number: JTF513.14. Type: Standard. Material: Steel. Fitment: Direct replaceme...
Please Note: requires modification if your old one has a block connector for the four wires as has Suzuki OEM number 32800-45220 These inclu...
Fits NGK B series plugs with threaded terminals. 120 degree elbow long type. 14mm. 5 kilo ohm. Terminal stud. Water resistant, vibration res...
