Brand: JT Sprockets. Position: Rear. Tooth Count: 41. JT Part Number: JTR834.41. Type: Standard. Material: Steel. Fitment: Direct replacemen...
Brand: JT Sprockets. Position: Rear. Tooth Count: 39. JT Part Number: JTR834.39. Type: Standard. Material: Steel. Fitment: Direct replacemen...
Please note: Some Honda NC50 Express machines were registered in 1979 but built to a later 1980 specification, which uses a different batter...
Thread 14mm x hex 13/16" x pitch 1.25mm. Heat range 7. Reach 12.7mm (1/2"). Standard 2.5mm copper core centre electrode. 0.7-0.8mm...
Brand: JT Sprockets. Position: Rear. Tooth Count: 35. JT Part Number: JTR834.35. Type: Standard. Material: Steel. Fitment: Direct replacemen...
Brand: JT Sprockets. Position: Rear. Tooth Count: 31. JT Part Number: JTR834.31. Type: Standard. Material: Steel. Fitment: Direct replacemen...
10 wires with female spade block and bullet connectors. 2 keys included.
Brand: JT Sprockets. Position: Rear. Tooth Count: 48. JT Part Number: JTR834.48. Type: Standard. Material: Steel. Fitment: Direct replacemen...
This engine gasket set contains most of the gaskets required for an engine rebuild. This gasket set does not include any oil seals other tha...
Brand: JT Sprockets. Position: Rear. Tooth Count: 30. JT Part Number: JTR834.30. Type: Standard. Material: Steel. Fitment: Direct replacemen...
27mm tapering down to 14mm. Length 32cm. Suitable replacement aftermarket part for Yamaha Fizzy OEM numbers: 348-14753-00, 296-14753-02.
This final drive chain is the correct length and pitch for standard factory fitted sprockets. Comes with a split link only. This may not be ...
Replacement front fork gaiters suitable for the Yamaha FS1-E and many other models with similar fork dimensions. Rubber compound for water r...
Thread 8mm. Spanner size 13mm. Pitch 1.25mm.
Outer diameter 14.50mm. Length 36.00mm. Thickness 2.00mm. Heavy duty clutch springs.
This kit includes the following parts: Con rod. Gudgeon pin. Big end and small end needle bearings. Pair of thrust washers.
This kit includes the following bearings: Bearing 1: ID 25mm x OD 48mm x Thickness 13mm. Bearing 2: ID 30mm x OD 48mm x Thickness 12mm.
Non-diaphragm tap type. Made in Japan.
Please Note: This speedo cable is 900mm (35.5") long so you may require a shorter version as listed below: Length: 35.5" (900mm). ...
Please Note: This speedo cable is 780mm/30.5" long so you may require a longer version as listed below: Length: 30.5" (780mm). Clo...
Inner diameter 30mm. Outer diameter 48mm. Width 12mm.
Note: The Fizzy FS1/FS1E used different condensers throughout models, so please check the image as you may need our SKU: 005012 with a singl...
Width 4" (100mm) at widest point. Length 25" (635mm). Replacement aftermarket part for the following Yamaha OEM numbers: 394-21610...
Replacement for FEW M48, M76, D92; Daiichi DM78, M76, DM79K, DH31, DN52, DM69; Honda OE 30202-041-015; Yamaha OE 1K8-81321-20, 120-81321-20,...
Outer diameter 14mm. Length 55mm. Spring length 51mm. Made in Japan. Replacement aftermarket part for Yamaha OEM 535-W0041-60, 535-20000-60a...
