Models including Fizzy FS1E, YB100, C50, C70, NC50, PA50 and many other models use a longer HT lead than this one at 300mm. If your original...
Fits NGK B series plugs with solid terminals. 90 degree elbow. 14mm. 5 kilo ohm. Terminal nut. Rubber sheathed. Compact type. Water resistan...
Steel sprocket. Replaces JT Sprockets JTR842-50.
Brake light switch with lead. Lead length 12cm. 2 wires with bullet connectors. Comes with spring. Replacement aftermarket part for Yamaha O...
Thread 14mm x hex 3/4" (19mm) x pitch 1.25mm. Ceramic resistor. Heat range 7. 19mm (3/4") reach. 0.6mm fine wire iridium centre el...
Thread 14mm x hex 13/16" x pitch 1.25mm. Heat range 7. Reach 19mm (3/4"). Standard 2.5mm copper core centre electrode. 0.7-0.8mm g...
This engine gasket set contains most of the gaskets required for an engine rebuild. This gasket set does not include any oil seals other tha...
This kit includes the following bearings: Bearing 1: ID 25mm x OD 43mm x Thickness 11mm. Bearing 2: ID 30mm x OD 48mm x Thickness 12mm.
2 bolt hole type. 34mm between bolt hole centres. Replacement aftermarket part for the following OEM numbers: Honda 95014-92100, 23811-230-0...
Outer diameter 14.50mm. Length 36.00mm. Thickness 2.00mm. Heavy duty clutch springs.
This kit includes the following parts: Con rod. Gudgeon pin. Big end and small end needle bearings. Pair of thrust washers.
Replacement aftermarket part for following OEM numbers: - Please Note: This is just for the needle valve as per image and does not include t...
Inner diameter 30mm. Outer diameter 48mm. Width 12mm.
This chain comes with a split link. This final drive chain is the correct length and pitch for standard factory fitted sprockets. Super Rein...
Made in Japan. This kit includes the following bearings: Bearing 1: ID 25mm x OD 43mm x Thickness 11mm. Bearing 2: ID 30mm x OD 48mm x Thick...
Includes all bearings and seals. Heavy duty tapered roller bearings. Direct replacement for OEM bearings. Upgrade replacement for ball style...
Non-Sealed economical chain for heavy duty usage. Made in Japan. Specifications Plate thickness (inner): 2.00. Plate thickness (outer): 2.00...
Bore size 66.50mm. Gudgeon pin outer diameter 16mm. Crown height 22.5mm. Piston length 63.5mm. Ring peg position 25.5mm. 2 stroke. With port...
Bore size 67.50mm. Gudgeon pin outer diameter 16mm. Crown height 22.5mm. Piston length 63.5mm. Ring peg position 25.5mm. 2 stroke. With port...
Bore size 66.00mm. Gudgeon pin outer diameter 16mm. Crown height 22.5mm. Piston length 63.5mm. Ring peg position 25.5mm. 2 stroke. With port...
Bore size 67.00mm. Gudgeon pin outer diameter 16mm. Crown height 22.5mm. Piston length 63.5mm. Ring peg position 25.5mm. 2 stroke. With port...
Replacement aftermarket part for for the following OEM numbers: Yamaha 207-81326-10-00, 207-81326-90-00. and many more TBA. This will suit t...
Replacement for DH-45, H85. Pivot pin length 25mm. Replacement aftermarket part for Yamaha OEM 443-81321-10. These will also fit a Yamaha DT...
Many models including Fizzy FS1E, YB100, C50, C70, NC50, PA50 and many others may use a longer HT lead than this one at 280mm which is non-r...
