Thread 14mm x hex 3/4" (19mm) x pitch 1.25mm. Ceramic resistor. Heat range 7. 12.7mm (1/2") reach. 0.6mm fine wire iridium centre ...
Models including Fizzy FS1E, YB100, C50, C70, NC50, PA50 and many other models use a longer HT lead than this one at 300mm. If your original...
Brake light switch with lead. Small push-in type. 2 wires with bullet connectors.
45 degree brake light switch with lead. 2 wires with bullet connectors. Comes with spring. Replacement aftermarket part for Yamaha OEM 1A0-8...
Brand: JT Sprockets. Position: Front. Tooth Count: 14. JT Part Number: JTF546.14. Type: Standard. Material: Steel. Fitment: Direct replaceme...
Brand: JT Sprockets. Position: Front. Tooth Count: 15. JT Part Number: JTF546.15. Type: Standard. Material: Steel. Fitment: Direct replaceme...
Brand: JT Sprockets. Position: Front. Tooth Count: 12. JT Part Number: JTF413.12. Type: Standard. Material: Steel. Fitment: Direct replaceme...
Please note: Some Honda NC50 Express machines were registered in 1979 but built to a later 1980 specification, which uses a different batter...
Brand: JT Sprockets. Position: Rear. Tooth Count: 32. JT Part Number: JTR834.32. Type: Standard. Material: Steel. Fitment: Direct replacemen...
Brand: JT Sprockets. Position: Rear. Tooth Count: 41. JT Part Number: JTR834.41. Type: Standard. Material: Steel. Fitment: Direct replacemen...
Thread 14mm x hex 13/16" x pitch 1.25mm. Heat range 7. Reach 12.7mm (1/2"). Standard 2.5mm copper core centre electrode. 0.7-0.8mm...
Brand: JT Sprockets. Position: Rear. Tooth Count: 35. JT Part Number: JTR834.35. Type: Standard. Material: Steel. Fitment: Direct replacemen...
This engine gasket set contains most of the gaskets required for an engine rebuild. This gasket set does not include any oil seals other tha...
Mounting hole centres: 80mm. Centre tab: 53mm. Length: 30mm. Width: 8mm. Includes 2 tabs, 4 bolts and 4 nuts. Once fitted and tight lock the...
Thread 8mm. Spanner size 13mm. Pitch 1.25mm.
Outer diameter 58mm. Inner diameter 47mm. Width 7mm.
This kit includes the following bearings: Bearing 1: ID 25mm x OD 48mm x Thickness 13mm. Bearing 2: ID 30mm x OD 48mm x Thickness 12mm.
Inner diameter 30mm. Outer diameter 48mm. Width 12mm.
This final drive chain is the correct length and pitch for standard factory fitted sprockets. Comes with a split link only. This may not be ...
Replacement for FEW M48, M76, D92; Daiichi DM78, M76, DM79K, DH31, DN52, DM69; Honda OE 30202-041-015; Yamaha OE 1K8-81321-20, 120-81321-20,...
Made in Japan. This kit includes the following bearings: Bearing 1: ID 25mm x OD 48mm x Thickness 13mm. Bearing 2: ID 30mm x OD 48mm x Thick...
Fits NGK B series plugs with threaded terminals. 90 degree elbow. 14mm. 5 kilo ohm. Terminal stud. Replacement aftermarket part for the foll...
Includes RJ Split Link - RJ type links are what we call a loose-clip type link. The side plate may be pressed on and the clip will slide int...
Single bolt hole mount. Outer diameter 75mm. 100 dB. All buyers please be aware that all horns/hooters supplied by us are marked but not nec...
Top 1 outer length: 635mm. Bottom 1 outer length: 580mm. Bottom 2 outer length: 385mm. Outer top 1 fitting: 90' bend, 10mm adjuster (1.00mm ...
