Outer diameter 96mm. Thickness 2.6mm. Number of pegs 17. Replacement for Vesrah VP1011. Replacement aftermarket part for the following OEM n...
Steel sprocket ID including splines: 15mm. ID without splines: 17mm. Gap between each spline: 4mm. Bolt hole centres: 28mm and 30mm. Number ...
Brake light switch with lead. 2 wires with bullet connectors. Replacement aftermarket part for the following OEM numbers: Honda 35350-086-72...
This clutch plate has friction material on both sides unlike others being sold elsewhere. Outer diameter (including teeth) 109mm. Thickness ...
Brand: JT Sprockets. Position: Front. Tooth Count: 15. JT Part Number: JTF253.15. Type: Standard. Material: Steel. Fitment: Direct replaceme...
Brand: JT Sprockets. Position: Front. Tooth Count: 14. JT Part Number: JTF253.14. Type: Standard. Material: Steel. Fitment: Direct replaceme...
Brand: JT Sprockets. Position: Front. Tooth Count: 13. JT Part Number: JTF253.13. Type: Standard. Material: Steel. Fitment: Direct replaceme...
Thread 10mm x hex 5/8" (16mm) x pitch 1.00mm. Ceramic resistor. Heat range 7. 12.7mm (1/2") reach. 0.6mm fine wire iridium centre ...
This engine gasket set contains most of the gaskets required for an engine rebuild. This gasket set does not include any oil seals other tha...
If your coil has 2 spades the second is for earth so before you fit the new one clean where it bolts to by scraping any paint or rust off th...
Four wires with male spade block connector. Plug-in mount. Two positions. Two keys included. Replacement aftermarket part for Honda OEM 3510...
Steel sprocket. Replaces JT Sprockets JTR257-40.
Thread 10mm x hex 5/8" (16mm) x pitch 1.00mm. Ceramic resistor. Heat range 7. 12.7mm (1/2") reach. Standard 2.5mm copper core cent...
Brand: JT Sprockets. Position: Rear. Tooth Count: 39. JT Part Number: JTR257.39. Type: Standard. Material: Steel. Fitment: Direct replacemen...
Brand: JT Sprockets. Position: Rear. Tooth Count: 40. JT Part Number: JTR257.40. Type: Standard. Material: Steel. Fitment: Direct replacemen...
Brand: JT Sprockets. Position: Rear. Tooth Count: 41. JT Part Number: JTR257.41. Type: Standard. Material: Steel. Fitment: Direct replacemen...
Brand: JT Sprockets. Position: Rear. Tooth Count: 36. JT Part Number: JTR257.36. Type: Standard. Material: Steel. Fitment: Direct replacemen...
This final drive chain is the correct length and pitch for standard factory fitted sprockets. Comes with a split link only. This may not be ...
Total length: 54.10mm. Length from under head to end of thread: 40.40mm. Fits sprocket carrier SKU: 002850. Replacement aftermarket part for...
Includes sprocket and bearing.
Endless cam chain. Length: 82 links. Pitch: 6.35mm. Roller width: 3.18mm. Overall width: 16.6mm. Made in Japan. Fitting Endless Cam Chains â...
This kit includes the following bearings: Bearing 1: ID 22.5mm x OD 41mm x Thickness 12.5mm. Bearing 2: ID 24mm x OD 41mm x Thickness 12.5mm...
Outer cable length: 710mm. Inner cable length: 57mm. Top cable fitting: 6mm stepped ferrule. Bottom cable fitting: standard ferrule. Top nip...
Includes rocker arms for inlet and exhaust. Replacement aftermarket part for Honda OEM 14431-035-020.
Outer diameter 33mm. Inner diameter 25.6mm. Depth 4mm. Copper Exhaust Header Gaskets otherwise known as Crush Gaskets fit with flat side of ...
Front Cover for Honda's listed that use a rectangle air filter. Replacement aftermarket part for Honda OEM 64301-087-710, 64301-041-690, 643...
Thread outer diameter 30mm. Pitch 1.50mm.
Top 1 outer length: 725mm. Outer top 1 fitting: 45' bend, 10mm adjuster. Outer bottom 1 fitting: standard ferrule. Top 1 inner overhang: 104...
