For use on 12v bulbs upto 23w.
Robust, lightweight, and weather resistant. Complete with bulbs and wiring.
Outer diameter 97mm. Thickness 1.5mm. Number of pegs 8.
Total lead length: 360mm. Longer lead at 630mm use our SKU: 036776. Front or rear brake light stop switch. Push in type. 8mm diameter. 2 wir...
Outer diameter 96mm. Thickness 2.6mm. Number of pegs 17. Replacement for Vesrah VP1011. Replacement aftermarket part for the following OEM n...
Steel sprocket ID including splines: 15mm. ID without splines: 17mm. Gap between each spline: 4mm. Bolt hole centres: 28mm and 30mm. Number ...
12V 4.7AH CCA 70. Terminals: 2 (1 positive + 1 negative). Complete with battery terminals & connections. Length: 114mm x Width: 70mm x H...
This clutch plate has friction material on both sides unlike others being sold elsewhere. Outer diameter (including teeth) 109mm. Thickness ...
Brand: JT Sprockets. Position: Front. Tooth Count: 13. JT Part Number: JTF253.13. Type: Standard. Material: Steel. Fitment: Direct replaceme...
Brand: JT Sprockets. Position: Front. Tooth Count: 14. JT Part Number: JTF253.14. Type: Standard. Material: Steel. Fitment: Direct replaceme...
Brake light switch with lead. 2 wires with bullet connectors. Replacement aftermarket part for the following OEM numbers: Honda 35350-086-72...
Thread 10mm x hex 5/8" (16mm) x pitch 1.00mm. Ceramic resistor. Heat range 7. 12.7mm (1/2") reach. 0.6mm fine wire iridium centre ...
This engine gasket set contains most of the gaskets required for an engine rebuild. This gasket set does not include any oil seals other tha...
12v Rectifier fits many models including those using the Chinese GY6 engine. Replaces Shindengen: SH591-12, SH634-12 SH570-6, SH570-12, SH61...
If your coil has 2 spades the second is for earth so before you fit the new one clean where it bolts to by scraping any paint or rust off th...
Four wires with male spade block connector. Plug-in mount. Two positions. Two keys included. Replacement aftermarket part for Honda OEM 3510...
Steel sprocket. Replaces JT Sprockets JTR257-40.
Brand: JT Sprockets. Position: Rear. Tooth Count: 40. JT Part Number: JTR257.40. Type: Standard. Material: Steel. Fitment: Direct replacemen...
Brand: JT Sprockets. Position: Rear. Tooth Count: 39. JT Part Number: JTR257.39. Type: Standard. Material: Steel. Fitment: Direct replacemen...
Brand: JT Sprockets. Position: Rear. Tooth Count: 41. JT Part Number: JTR257.41. Type: Standard. Material: Steel. Fitment: Direct replacemen...
Brand: JT Sprockets. Position: Rear. Tooth Count: 36. JT Part Number: JTR257.36. Type: Standard. Material: Steel. Fitment: Direct replacemen...
Thread 10mm x hex 5/8" (16mm) x pitch 1.00mm. Ceramic resistor. Heat range 7. 12.7mm (1/2") reach. Standard 2.5mm copper core cent...
Includes sprocket and bearing.
This kit includes the following bearings: Bearing 1: ID 22.5mm x OD 41mm x Thickness 12.5mm. Bearing 2: ID 24mm x OD 41mm x Thickness 12.5mm...
Total length: 54.10mm. Length from under head to end of thread: 40.40mm. Fits sprocket carrier SKU: 002850. Replacement aftermarket part for...
Replacement aftermarket part for Honda OEM 61100-GB4-680.
This final drive chain is the correct length and pitch for standard factory fitted sprockets. Comes with a split link only. This may not be ...
Includes rocker arms for inlet and exhaust. Replacement aftermarket part for Honda OEM 14431-035-020.