Koyo 6306NR. Outer diameter 72mm. Inner diameter 30mm. Width 19mm. Made in Japan.
Replacement aftermarket part for the following OEM numbers: Honda 15412-413-000/005, 15412-KEA-003, 154A1-413-000, 15412-KK9-911, 154A1-MA6-...
Brand cross reference: Vesrah VD117, 45, Ferodo FDB183, SBS 526. You may need more than a single pair of pads if you have twin discs. Goldfr...
Thread 12mm x hex 18mm x pitch 1.25mm. Ceramic resistor. Heat range 8. 19mm (3/4") reach. 0.6mm fine wire iridium centre electrode. 0.7...
This engine gasket set contains most of the gaskets required for an engine rebuild. This gasket set does not include any oil seals other tha...
Round body. Body small OD 30mm. Body large OD 35mm. Length 34mm. Length + pins 46.8mm. For use with all bulbs. Includes buzzer.
Fits NGK D series plugs with threaded terminals. 102 degree elbow. 10-12mm. 5 kilo ohm. 70mm from end to elbow. Terminal stud. Replacement a...
Round body. Body small OD 33.5mm. Body large OD 36.5mm. Length 43mm. Length + pins 55.5mm. For use with all bulbs. Includes buzzer.
Mounting hole centres: 50mm. Wires with male terminals in block connector: 6. These will suit the following models as well as those listed i...
12V 11AH CCA 140. Terminals: 4 (2 positive + 2 negative). Complete with battery terminals & connections. Battery can be rotated 180 degr...
Steel sprocket. Replaces JT Sprockets JTF281-15.
Steel sprocket. Replaces JT Sprockets JTF281-14.
NGK DR8ES-L (2923). Thread Diameter: 12mm (M12). Thread Pitch: 1.25mm. Seat Type: Gasket. Reach:19mm. Hex Size: 18mm. Terminal Type: Thread ...
Replacement aftermarket part for Honda OEM 35340-422-003, 35340-422-013.
Note: The wire ends may need modification and the hole centres are 90mm but we are aware that some models are 84mm so will also need modific...
Brand: JT Sprockets. Position: Front. Tooth Count: 15. JT Part Number: JTF281.15. Type: Standard. Material: Steel. Fitment: Direct replaceme...
Brand: JT Sprockets. Position: Front. Tooth Count: 14. JT Part Number: JTF281.14. Type: Standard. Material: Steel. Fitment: Direct replaceme...
Brand: JT Sprockets. Position: Rear. Tooth Count: 44. JT Part Number: JTR248.44. Type: Standard. Material: Steel. Fitment: Direct replacemen...
Type: K1. 4.40mm x 13.60mm. Can use with or without clip. Made in Japan. Replacement aftermarket part for the following OEM numbers: (Note: ...
Fits cam chains supplied by us only.
Outer diameter 11mm. Inner diameter 7.75mm. Stem 5.3mm.
Length: 38" (960mm). Other lengths are available 1060mm SKU: 015925 840mm SKU: 015905. Clock fit: screw-over 11mm. Bottom end: push-in ...
Outer diameter 18.20mm. Length 37.00mm. Thickness 2.80mm. Heavy duty clutch springs.
Length 70mm. Width 48mm. 2 screw cap - some originals have 4 screws but its a straight forward replacement. Supplied with diaphragm, O-ring ...
This kit includes the following bearings: Bearing 1: ID 26mm x OD 48.5mm x Thickness 15mm. Bearing 2: ID 30mm x OD 50mm x Thickness 14mm.
108mm ID. 125mm OD without pegs. 136mm OD with pegs. 14mm width of peg. Number of pegs 10. 3.0mm thickness. Replacement for Vesrah VP1034. R...
This final drive chain is the correct length and pitch for standard factory fitted sprockets. Comes with a split link. Not recommended for M...
48mm is the outside diameter of your carburettor intake. Overall length including rubber 58mm. Lower width maximum OD 83mm.
Piston outer diameter 43mm. Each kit contains an inner oil seal and an outer dust seal. Enough seals for 5 pistons. Made in Japan. Fit Japan...
