Brand: JT Sprockets. Position: Rear. Tooth Count: 41. JT Part Number: JTR486.41. Type: Standard. Material: Steel. Fitment: Direct replacemen...
Brand: JT Sprockets. Position: Rear. Tooth Count: 38. JT Part Number: JTR486.38. Type: Standard. Material: Steel. Fitment: Direct replacemen...
Brand: JT Sprockets. Position: Rear. Tooth Count: 47. JT Part Number: JTR486.47. Type: Standard. Material: Steel. Fitment: Direct replacemen...
12V 14AH CCA 200. Yellow Version: Motobatt MBTX12U. Same battery in black use our SKU: 023262. Terminals: 4 (2 positive + 2 negative). Compl...
12V 14AH CCA 200. Black Version: Motobatt MBTX12UHD. Same battery in yellow use our SKU: 004738. Terminals: 4 (2 positive + 2 negative). Com...
Brake light switch with lead. Lead length 10cm. 2 wires with male block connector. Replacement aftermarket part for Kawasaki OEM 27010-1452.
Thread 12mm x hex 18mm x pitch 1.25mm. Ceramic resistor. Heat range 9. 19mm (3/4") reach. 0.6mm fine wire iridium centre electrode. 0.7...
This will suit the following models as well as those listed in fitments: Kawasaki ER-5 Twister (35ps) & (50ps) 1999.
55mm between bolt hole centres. 6 wires. Made in Japan. Regulator/Rectifier Fitting InstructionsWhen on test, 12 Volt batteries should show ...
Thread 12mm x hex 18mm x pitch 1.25mm. Ceramic resistor. Heat range 9. 19mm (3/4") reach. Special design. 0.7-0.8mm gap.
Replacement aftermarket part for the following OEM numbers: Kawasaki 11013-1261. This will suit the following models as well as those listed...
Outer diameter 10mm. Inner diameter 7.75mm. Stem 4.5mm.
This chain comes with a split link. This final drive chain is the correct length and pitch for standard factory fitted sprockets. The RXP ch...
Piston outer diameter 30mm. Oil seal: 3.00mm wide x 3.20mm thick. Dust seal: 2.15mm wide x 2.15mm thick. This kit contains an inner oil seal...
Piston outer diameter 30mm. Each kit contains an inner oil seal and an outer dust seal. Enough seals for 5 pistons. Fit Japanese bikes only ...
Suitable for Sport, Touring and Off-Road Use. RX-Ring Chain. Standard Sealed Chain. Made in Japan. Specifications Plate thickness (inner): 2...
Outer diameter 19.75mm. Length 33.00mm. Thickness 2.80mm. Heavy duty clutch springs.
Upper or Lower depending on whether standard or USD forks. Outer diameter 41mm. Inner diameter 37.1mm. Width 12mm. Thickness 1.95mm.
Non-Sealed economical chain for heavy duty usage. Made in Japan. Specifications Plate thickness (inner): 2.30. Plate thickness (outer): 2.30...
Suitable for Sport, Touring and Off-Road Use. RX-Ring Chain. Standard Sealed Chain. Made in Japan. RK XSO Series: Designed for Basic Motorcy...
Please note: This brake pad pin kit is supplied exactly as shown in the image. Depending on the caliper design, some applications use one re...
Inner diameter 30mm. Outer diameter 48mm. Width 14mm.
Suitable for early Japanese motorcycles up to 500cc. Black body and spring. 350mm centre to centre of bolt holes. Top pin hole ID 14mm - wid...
Inner diameter 30mm. Outer diameter 52mm. Width 16mm. Made in Japan.
Outer diameter 47mm. Inner diameter 38mm approx. Depth 5mm. Copper Exhaust Header Gaskets otherwise known as Crush Gaskets fit with flat sid...
Piston outer diameter 34mm. Each kit contains an inner oil seal and an outer dust seal. Enough seals for 5 pistons. Made in Japan. Fit Japan...
This wheel bearing kit uses premium quality Japanese Koyo bearings.
Brand cross reference: Vesrah VD435; 229, 237; Ferodo FDB2048; SBS 705; Dunlopad DP322. Kyoto organic GG brake disc pads. You may need more ...
Steel sprocket. Replaces JT Sprockets JTR486-40.
Steel sprocket. Replaces JT Sprockets JTR486-35.
