Models including Fizzy FS1E, YB100, C50, C70, NC50, PA50 and many other models use a longer HT lead than this one at 300mm. If your original...
Brand: JT Sprockets. Position: Rear. Tooth Count: 37. JT Part Number: JTR801.37. Type: Standard. Material: Steel. Fitment: Direct replacemen...
Brand: JT Sprockets. Position: Rear. Tooth Count: 41. JT Part Number: JTR801.41. Type: Standard. Material: Steel. Fitment: Direct replacemen...
For use with bulbs up to 10 watt.
Brand: JT Sprockets. Position: Rear. Tooth Count: 36. JT Part Number: JTR801.36. Type: Standard. Material: Steel. Fitment: Direct replacemen...
Brand: JT Sprockets. Position: Rear. Tooth Count: 34. JT Part Number: JTR801.34. Type: Standard. Material: Steel. Fitment: Direct replacemen...
Brand: JT Sprockets. Position: Rear. Tooth Count: 32. JT Part Number: JTR801.32. Type: Standard. Material: Steel. Fitment: Direct replacemen...
Please note: Some Honda NC50 Express machines were registered in 1979 but built to a later 1980 specification, which uses a different batter...
Outer diameter 47mm. Inner diameter 23mm. Width 8mm.
Thread 14mm x hex 3/4" (19mm) x pitch 1.25mm. Projected insulator. Ceramic resistor. Heat range 4. 12.7mm (1/2") reach. Standard 2...
Replacement aftermarket part for the following OEM numbers: Yamaha 22F-26341-00, 22F-26341-01, 22F-26341-02. Suzuki 58100-26000, 58100-01722...
Suitable for mirrors with part numbers 011958, 011966, 011957. And any other mirrors with 10mm right hand thread (clockwise).
These piston kits do not have Dyke rings but your bike will run perfectly fine with the supplied square rings. Bore size 43.00mm. Gudgeon pi...
Thread 8mm. Spanner size 13mm. Pitch 1.25mm.
50mm between hole centres.
These piston kits do not have Dyke rings but your bike will run perfectly fine with the supplied square rings. Bore size 42.00mm. Gudgeon pi...
Outer diameter 16mm. Inner diameter 12mm. Length 16mm.
Outer diameter 42mm. Inner diameter 33mm. Depth 4mm. Copper Exhaust Header Gaskets otherwise known as Crush Gaskets fit with flat side of th...
Outer diameter 110mm. Replacement aftermarket part for Suzuki OEM 64651-01001.
Outer diameter 42mm. Inner diameter 32mm. Depth 4mm. Flat Copper Exhaust Header Gaskets fit with flat side of the gasket against the cylinde...
Non-asbestos. Outer diameter 42mm. Inner diameter 34mm. Alloy Fibre Exhaust Header Gaskets are two aluminium bands with compressible paper f...
10mm spline size. 115mm length between centre of toe plate and centre of spline.
Length: 35" (890mm). Clock fit: screw-over 11mm. Wheel end: screw-over 10mm. Type: square/fork. Shorter cable 760mm use our SKU: 015928...
This final drive chain is the correct length and pitch for standard factory fitted sprockets. Comes with a split link only. This may not be ...
These piston kits do not have Dyke rings but your bike will run perfectly fine with the supplied square rings. Bore size 41.50mm. Gudgeon pi...
These piston kits do not have Dyke rings but your bike will run perfectly fine with the supplied square rings. Bore size 41.00mm. Gudgeon pi...
These piston kits do not have Dyke rings but your bike will run perfectly fine with the supplied square rings. Bore size 45.25mm. Gudgeon pi...
