Inner diameter 41mm. Outer diameter 54mm. Thickness 11mm.
Koyo 32006JR. Inner diameter 30mm. Outer diameter 55mm. Width 17mm. Made in Japan. Replacement aftermarket part for the following OEM number...
Includes the electric fuel pump and parts needed to service or rebuild the factory fuel pump module - check image/s. Works Racing Parts (WRP...
Kit contains a pair of fork oil seals and a pair of fork dust seals. Dyno tested to last 3 to 4 times longer than OEM seals. Directional rib...
Brake caliper shaft boots are the rubber sleeves that protect the slide bolts. Replacement aftermarket part for Honda OEM 45133-MA3-006, 451...
Kit contains a pair of fork dust seals.
Inner diameter 41mm. Outer diameter 54mm. Thickness 12.5mm.
Voltage: 12v. Wattage: 1.70W. Base width: 9.5mm. Maximum length: 27mm. T10 (also known as W5W or 501). Uses of Small T10 Capless Wedge Bulbs...
Thread 10mm. Spanner size 14mm. Replacement aftermarket part for the following OEM numbers: . Honda 90304-KAE-871, 90308-357-000, 90308-382-...
Outer diameter 20mm. Inner diameter 8mm. Length 40mm. Push-over style. Open both ends.
Includes a pair of fork oil seals and a pair of fork dust deals. Fork oil seals: ID 41mm x OD 54mm x Thickness 11mm. Push-in type fork dust ...
Brake caliper shaft boots are the rubber sleeves that protect the slide bolts. Replacement aftermarket part for Honda OEM 45132-166-016.
Please note: This brake pad pin kit is supplied exactly as shown in the image. Depending on the caliper design, some applications use one re...
Outer diameter 40mm. Inner diameter 25.5mm. Thickness 3mm.
Upper or Lower depending on whether standard or USD forks. Outer diameter 45mm. Inner diameter 41mm. Width 14.9mm. Thickness 2mm.
Replacement aftermarket part for the following OEM numbers: Honda: 34901-MAT-611, 33110-S1A-G51, 33110-SMG-E01HE, 34901-KEY-700, 34901-MGZ-J...
Voltage: 12v. Wattage: 10w. Maximum width of base: 9.5mm. Maximum width of glass: 15.7mm. Maximum length: 39.3mm. Uses of Large T15 Capless ...
Piston outer diameter 30mm. Oil seal: 3.00mm wide x 3.20mm thick. Dust seal: 2.15mm wide x 2.15mm thick. Each kit contains an inner oil seal...
Voltage: 12v. Wattage: 3.4w. Base width: 9.5mm. Glass: 10mm. Maximum length: 26.8mm. Uses of Small T10 Capless Wedge Bulbs. Small T10 caples...
This 32006JRRS bearing comes with the seal as shown in the image. Koyo 32006JRRS. Inner diameter: 30mm. Outer diameter: 55mm. Width: 17mm. M...
Kelvin is a measurement by colour temperature of the colour produced to a halogen bulb. Colour temperature refers to how warm or cool a bulb...
Voltage: 12v. Wattage: 5w. Base width: 8mm. Maximum width of glass: 10mm. Maximum length: 25.6mm. Uses of Medium T13 Capless Wedge Bulbs. Me...
For the Moto Guzzi MGS-01 Corsa (1225cc): Two bearings are required for the front wheel and two for the rear wheel. Koyo: 6005DDU, 6005-2RS-...
Smallest of the two mechanical water pump seals fitted in mainly Suzuki models. Outer diameter 24mm/29mm. Inner diameter 11.15mm/22.5mm. Wid...
Includes all the parts you need for one caliper. OEM replacement, meets or exceeds OEM specs.
This oil filter remover will only fit filters supplied by Motorcycle Products.
Thread diameter 49mm. Supplied with diaphragm, O-ring and screw. Made in Japan. The O-ring is not used on Suzuki models.
Outer diameter 22mm. Inner diameter 14mm. Width 5mm.
