10 wires with female spade block and bullet connectors. 2 keys included.
This engine gasket set contains most of the gaskets required for an engine rebuild. This gasket set does not include any oil seals other tha...
Brand: JT Sprockets. Position: Rear. Tooth Count: 35. JT Part Number: JTR834.35. Type: Standard. Material: Steel. Fitment: Direct replacemen...
Brand: JT Sprockets. Position: Rear. Tooth Count: 31. JT Part Number: JTR834.31. Type: Standard. Material: Steel. Fitment: Direct replacemen...
Brand: JT Sprockets. Position: Rear. Tooth Count: 48. JT Part Number: JTR834.48. Type: Standard. Material: Steel. Fitment: Direct replacemen...
Brand: JT Sprockets. Position: Rear. Tooth Count: 30. JT Part Number: JTR834.30. Type: Standard. Material: Steel. Fitment: Direct replacemen...
This final drive chain is the correct length and pitch for standard factory fitted sprockets. Comes with a split link only. This may not be ...
Replacement front fork gaiters suitable for the Yamaha FS1-E and many other models with similar fork dimensions. Rubber compound for water r...
27mm tapering down to 14mm. Length 32cm. Suitable replacement aftermarket part for Yamaha Fizzy OEM numbers: 348-14753-00, 296-14753-02.
Outer diameter 14.50mm. Length 36.00mm. Thickness 2.00mm. Heavy duty clutch springs.
This kit includes the following parts: Con rod. Gudgeon pin. Big end and small end needle bearings. Pair of thrust washers.
Replacement aftermarket part for the following OEM numbers: Honda 42711-GK4-605, 44711-GB6-882, 42711-GK4-603, 42711-GK4-604, 42711-GK4-602,...
Includes RJ Split Link - RJ type links are what we call a loose-clip type link. The side plate may be pressed on and the clip will slide int...
Non-diaphragm tap type. Made in Japan.
This kit includes the following bearings: Bearing 1: ID 25mm x OD 48mm x Thickness 13mm. Bearing 2: ID 30mm x OD 48mm x Thickness 12mm.
Note: The Fizzy FS1/FS1E used different condensers throughout models, so please check the image as you may need our SKU: 005012 with a singl...
Please Note: This speedo cable is 780mm/30.5" long so you may require a longer version as listed below: Length: 30.5" (780mm). Clo...
This final drive chain is the correct length and pitch for standard factory fitted sprockets. This may not be the most suitable grade of fin...
Inner diameter 30mm. Outer diameter 48mm. Width 12mm.
Width 4" (100mm) at widest point. Length 25" (635mm). Replacement aftermarket part for the following Yamaha OEM numbers: 394-21610...
Replacement for FEW M48, M76, D92; Daiichi DM78, M76, DM79K, DH31, DN52, DM69; Honda OE 30202-041-015; Yamaha OE 1K8-81321-20, 120-81321-20,...
Outer diameter 39mm. Inner diameter 29mm. Depth 4mm. Flat Copper Exhaust Header Gaskets fit with flat side of the gasket against the cylinde...
Outer diameter 15.8mm. Length 52mm. Spring length 43mm. Made in Japan. Replacement aftermarket part for the following OEM numbers: Kawasaki ...
Made in Japan. This kit includes the following bearings: Bearing 1: ID 25mm x OD 48mm x Thickness 13mm. Bearing 2: ID 30mm x OD 48mm x Thick...
Fits NGK B series plugs with threaded terminals. 90 degree elbow. 14mm. 5 kilo ohm. Terminal stud. Replacement aftermarket part for the foll...
