Brand: JT Sprockets. Position: Front. Tooth Count: 14. JT Part Number: JTF1263.14. Type: Standard. Material: Steel. Fitment: Direct replacem...
Brand: JT Sprockets. Position: Front. Tooth Count: 15. JT Part Number: JTF1263.15. Type: Standard. Material: Steel. Fitment: Direct replacem...
Includes RJ Split Link - RJ type links are what we call a loose-clip type link. The side plate may be pressed on and the clip will slide int...
Outer diameter (including teeth) 124mm. Thickness 3.2mm. Number of pegs 8. Replacement for Vesrah VP2003/2.
Aftermarket black resistor spark plug cap, equivalent to NGK LB05F and designed for use with 14mm spark plugs that have an exposed threaded ...
For use with bulbs up to 23 watt. B = Battery. L = Indicator. If the shape of your relay is rectangle you can still fit this round one which...
Thread 14mm x hex 3/4" (19mm) x pitch 1.25mm. Ceramic resistor. Heat range 8. 12.7mm (1/2") reach. 0.6mm fine wire iridium centre ...
If your coil has 2 spades the second is for earth so before you fit the new one clean where it bolts to by scraping any paint or rust off th...
Steel sprocket. Replaces JT Sprockets JTR838-39.
Steel sprocket. Replaces JT Sprockets JTR838-45.
Steel sprocket. Replaces JT Sprockets JTR838-36.
Steel sprocket. Replaces JT Sprockets JTR838-37.
Please note: Some Honda NC50 Express machines were registered in 1979 but built to a later 1980 specification, which uses a different batter...
Thread 14mm x hex 3/4" (19mm) x pitch 1.25mm. Ceramic resistor. Heat range 8. 12.7mm (1/2") reach. Standard 2.5mm copper core cent...
Brand: JT Sprockets. Position: Rear. Tooth Count: 45. JT Part Number: JTR838.45. Type: Standard. Material: Steel. Fitment: Direct replacemen...
Brand: JT Sprockets. Position: Rear. Tooth Count: 39. JT Part Number: JTR838.39. Type: Standard. Material: Steel. Fitment: Direct replacemen...
Brand: JT Sprockets. Position: Rear. Tooth Count: 37. JT Part Number: JTR838.37. Type: Standard. Material: Steel. Fitment: Direct replacemen...
Brand: JT Sprockets. Position: Rear. Tooth Count: 36. JT Part Number: JTR838.36. Type: Standard. Material: Steel. Fitment: Direct replacemen...
6 wires with male spade block connector. 2 keys included.
This engine gasket set contains most of the gaskets required for an engine rebuild. This gasket set does not include any oil seals other tha...
Downpipe to silencer gasket. Outer diameter 48.8mm. Inner diameter 40.5mm. Thickness 10mm. Replacement aftermarket part for Yamaha OEM 3FL-1...
Complete set of rear wheel hub rubber dampers otherwise known as cush drive rubbers. Length 76mm. Width 41mm. Replacement aftermarket part f...
This kit includes the following bearings: Bearing 1: ID 25mm x OD 43mm x Thickness 11mm. Bearing 2: ID 30mm x OD 48mm x Thickness 12mm.
2 bolt hole type. 34mm between bolt hole centres. Replacement aftermarket part for the following OEM numbers: Honda 95014-92100, 23811-230-0...
35mm is the outside diameter of your carburettor intake. Filter is 43mm long.
Non-diaphragm tap type. Made in Japan.
Length: 27.5" (700mm). Clock fit: screw over 11mm. Tacho drive end: push in 19mm. Inner type: square/square.
