These steering head tapered bearing kits are provided by Hendler to the same specification as the All Balls kits. While the quality is compa...
This engine gasket set contains most of the gaskets required for an engine rebuild. This gasket set does not include any oil seals other tha...
Brake light switch with lead. 2 wires with bullet connectors. Replacement aftermarket part for the following OEM numbers: Honda 35350-086-72...
Outer diameter 30mm. Inner diameter 19mm. Width 5mm.
Outer diameter 97mm. Thickness 1.5mm. Number of pegs 8.
12V 4.7AH CCA 70. Terminals: 2 (1 positive + 1 negative). Complete with battery terminals & connections. Length: 114mm x Width: 70mm x H...
Outer diameter 96mm. Thickness 2.6mm. Number of pegs 17. Replacement for Vesrah VP1011. Replacement aftermarket part for the following OEM n...
This clutch plate has friction material on both sides unlike others being sold elsewhere. Outer diameter (including teeth) 109mm. Thickness ...
Steel sprocket ID including splines: 15mm. ID without splines: 17mm. Gap between each spline: 4mm. Bolt hole centres: 28mm and 30mm. Number ...
Fits NGK D series plugs with threaded terminals. 90 degree elbow. 10-12mm. 5 kilo ohm. Terminal stud. Water resistant, vibration resistant a...
Steel sprocket. Replaces JT Sprockets JTR211-39.
Thread 10mm x hex 5/8" (16mm) x pitch 1.00mm. Ceramic resistor. Heat range 7. 12.7mm (1/2") reach. 0.6mm fine wire iridium centre ...
Steel sprocket. Replaces JT Sprockets JTR211-36.
If your coil has 2 spades the second is for earth so before you fit the new one clean where it bolts to by scraping any paint or rust off th...
Four wires with male spade block connector. Plug-in mount. Two positions. Two keys included. Replacement aftermarket part for Honda OEM 3510...
Brand: JT Sprockets. Position: Front. Tooth Count: 15. JT Part Number: JTF253.15. Type: Standard. Material: Steel. Fitment: Direct replaceme...
Brand: JT Sprockets. Position: Front. Tooth Count: 14. JT Part Number: JTF253.14. Type: Standard. Material: Steel. Fitment: Direct replaceme...
Thread 10mm x hex 5/8" (16mm) x pitch 1.00mm. Ceramic resistor. Heat range 7. 12.7mm (1/2") reach. Standard 2.5mm copper core cent...
Brand: JT Sprockets. Position: Rear. Tooth Count: 39. JT Part Number: JTR211.39. Type: Standard. Material: Steel. Fitment: Direct replacemen...
Wheel spokes that suit many Honda C90 models, please check fitments to see if these are listed as fitting your model. Set includes 36 spokes...
Total length: 54.10mm. Length from under head to end of thread: 40.40mm. Fits sprocket carrier SKU: 002850. Replacement aftermarket part for...
Total width approx 540mm. Note: this bar step may require touch up where paint is missing. Replacement aftermarket part for Honda OEM 50610-...
Clear version 12V 10W BA15s: SKU: 018209. Replacement aftermarket part for the following OEM numbers: Yamaha 1JD-H3311-00-00, 5SK-H3311-00-0...
Includes sprocket and bearing.
Outer cable length: 710mm. Inner cable length: 57mm. Top cable fitting: 6mm stepped ferrule. Bottom cable fitting: standard ferrule. Top nip...
This final drive chain is the correct length and pitch for standard factory fitted sprockets. Comes with a split link only. This may not be ...
Overall length 195mm. Replacement aftermarket part for Honda OEM 28251-086-701.
