12V 4.7AH CCA 70. Terminals: 2 (1 positive + 1 negative). Complete with battery terminals & connections. Length: 114mm x Width: 70mm x H...
Steel sprocket ID including splines: 15mm. ID without splines: 17mm. Gap between each spline: 4mm. Bolt hole centres: 28mm and 30mm. Number ...
This clutch plate has friction material on both sides unlike others being sold elsewhere. Outer diameter (including teeth) 109mm. Thickness ...
Please Note: This gasket set does not include left hand casing gasket which is the starter motor side. We suggest using one of our gasket ma...
Brake light switch with lead. 2 wires with bullet connectors. Replacement aftermarket part for the following OEM numbers: Honda 35350-086-72...
Brand: JT Sprockets. Position: Front. Tooth Count: 15. JT Part Number: JTF253.15. Type: Standard. Material: Steel. Fitment: Direct replaceme...
Brand: JT Sprockets. Position: Front. Tooth Count: 14. JT Part Number: JTF253.14. Type: Standard. Material: Steel. Fitment: Direct replaceme...
Brand: JT Sprockets. Position: Front. Tooth Count: 13. JT Part Number: JTF253.13. Type: Standard. Material: Steel. Fitment: Direct replaceme...
Fits NGK D series plugs with threaded terminals. 90 degree elbow. 10-12mm. Resistor type rated at 5kΩ. Terminal stud. Water resistant, vibr...
Thread 10mm x hex 5/8" (16mm) x pitch 1.00mm. Ceramic resistor. Heat range 7. 12.7mm (1/2") reach. 0.6mm fine wire iridium centre ...
Steel sprocket. Replaces JT Sprockets JTR211-39.
Steel sprocket. Replaces JT Sprockets JTR211-36.
If your coil has 2 spades the second is for earth so before you fit the new one clean where it bolts to by scraping any paint or rust off th...
Four wires with male spade block connector. Plug-in mount. Two positions. Two keys included. Replacement aftermarket part for Honda OEM 3510...
Thread 10mm x hex 5/8" (16mm) x pitch 1.00mm. Ceramic resistor. Heat range 7. 12.7mm (1/2") reach. Standard 2.5mm copper core cent...
Brand: JT Sprockets. Position: Rear. Tooth Count: 39. JT Part Number: JTR211.39. Type: Standard. Material: Steel. Fitment: Direct replacemen...
Includes rocker arms for inlet and exhaust. Replacement aftermarket part for Honda OEM 14431-035-020.
Wheel spokes that suit many Honda C90 models, please check fitments to see if these are listed as fitting your model. Set includes 36 spokes...
This kit includes the following bearings: Bearing 1: ID 22.5mm x OD 41mm x Thickness 12.5mm. Bearing 2: ID 24mm x OD 41mm x Thickness 12.5mm...
This hub will only fit front wheels supplied by us. It does not fit OEM factory standard wheels. Compatible parts: Chrome rim - SKU: 023808....
Pivot pin required for this stand SKU: 012954. Fits several Honda C90 models Check Fitments. Replacement aftermarket part for Honda OEM 5050...
Includes sprocket and bearing.
Total length: 54.10mm. Length from under head to end of thread: 40.40mm. Fits sprocket carrier SKU: 002850. Replacement aftermarket part for...
New product which may show traces of oxidation that can be polished out. Please check fitments to see if this part fits your model. Diameter...
Outer cable length: 710mm. Inner cable length: 57mm. Top cable fitting: 6mm stepped ferrule. Bottom cable fitting: standard ferrule. Top nip...
This final drive chain is the correct length and pitch for standard factory fitted sprockets. Comes with a split link only. This may not be ...
